Faux Wood Blinds

Faux Wood Blinds in New Palestine, IN

Moisture proof slats for New Palestine wet rooms and wide openings

Call (317) 854-7158Get Free Quote
Quick Answer

Here's the detail behind the product description. What it's made of, how it's sized, what drives the price, how long it takes to build and what the manufacturer covers if it fails.

  • Service: Faux Wood Blinds for New Palestine homeowners
  • Service area: New Palestine, IN and surrounding areas
    • Nothing in this trade is an urgent call-out, so here's the real timeline. Measures get scheduled promptly at a time that suits you. Custom fabrication then runs roughly two to five weeks. Installation is a morning or a day.
  • Insured and bonded
  • Serving New Palestine, IN since 2008
Faux Wood Blinds Services

Expert Faux Wood Blinds for New Palestine Homes

Faux wood is the default slat in New Palestine, and the reason is humidity rather than budget. Central Indiana's muggy stretch runs from about May 25 to September 22, then the year turns over to a January average low of 20.9 degrees. That swing moves solid lumber. PVC and composite slats sit still through it. So they belong in the 483 houses this town built between 2000 and 2019, and the Cedar Creek and Cedar Cove streets show the pattern: a 16 to 24 opening plan puts a blind in a laundry room and another over the kitchen sink, both places real wood eventually regrets.

The honest limit is span. A 2 inch PVC slat run past roughly six feet bows in the middle under its own weight, and heat speeds that up. It matters on the west side of town. Boulder Creek and the Countryside streets sit on the Sugar Creek Township section grid, so streets run true north and south and one side elevation of every house takes the low afternoon sun at the same angle. Past six feet we'd rather split the opening into two blinds under a single valance, or step up to a composite slat with a center support bracket. Composite also refuses stain, so against stained casing we match paint and say plainly that it's a compromise.

When to Call

Signs You Need Faux Wood Blinds

If you notice any of these in your New Palestine home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

You are buying blinds for a house you plan to sell

A wide headrail settles in the middle when lowered

The bathroom still has a vinyl roller from move-in

You want the look of wood in a wet room

A new bathroom went in and the windows are bare

Basement openings have never had anything on them

You added a window and the old white no longer matches

The blind above the kitchen sink looks swollen

Wood blinds over the tub have started to cup

A rental turnover needs blinds that survive tenants

Our Process

How New Palestine Window Treatments Handles Faux Wood Blinds

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Mounting depth taken

2

PVC or composite chosen

3

Wide spans get support brackets

4

Cordless or wand tilt chosen

5

Finished sizes recorded per opening

Real Project Photos

Faux Wood Blinds in New Palestine

Photographs from real faux wood blinds jobs completed by our crew in New Palestine and surrounding areas.

Custom shades measured and installed in New PalestinePlantation shutters fitted to a New Palestine windowCellular shades in a New Palestine living room
Scope of Work

What Faux Wood Blinds Includes

Every New Palestine job is documented item by item. Here is what the crew covers.

Every opening measured three widths and three heights, then checked corner to corner for square

Room moisture read before the material call, so baths, kitchens, laundry rooms and finished basements get faux wood

Mounting depth taken at the top of the opening so a 2 inch headrail clears the trim and any hardware

Solid PVC and wood-polymer composite separated on the order, because they don't weigh the same or behave the same

West and south openings flagged, since surface heat on a dark slat is what starts a bow

Slat size set per opening, 2 inch as the standard and 2 1/2 inch where the window is wide enough to carry it

Center support bracket planned on any span wide enough to let a loaded headrail settle in the middle

Wide openings split two-on-one so no single blind carries more weight than its brackets should

Finished weight checked against the opening before a wide unit gets ordered as one piece

Routeless slats specified where a row of lit route holes would be noticed from inside the room

Cloth tape ladders offered where the route holes should disappear behind a band of fabric

Tilt wand set as the default, with cord tilt only where a wand can't clear a handle or a return

Cordless lift specified in rooms that kids and pets actually use

Products specified to conform to ANSI/WCMA A100.1-2022 for cord access

Valance style and return depth chosen so an outside mount really closes off the sides

Factory deduction left with the manufacturer so the allowance never gets taken twice

Light gap per side written onto the paperwork before the order goes to the factory

Old blinds pulled, brackets removed, and every new unit tilted and lifted end to end before we leave

Pricing

What Faux Wood Blinds Cost in New Palestine

National category figures put stock blinds and shades near $60 to $600 a window, with custom-fabricated units running roughly $250 to $2,600. Those are published national ranges for the category, not a quote for any address in New Palestine. Faux wood lands low in that band, which is most of why people choose it. A 2 inch composite blind on an ordinary bathroom opening is inexpensive work. Price climbs when the opening gets wide, because weight is the real constraint here: a wide span wants a center support bracket or a two-on-one headrail, and both add parts and install time. Routeless slats, cloth tapes and a cordless lift each move the number as well. New Palestine Window Treatments prices from measured openings around Hancock County, never from a per-window average.

By Product

How Faux Wood Blinds Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

2 inch faux wood slat: The size most houses around here want, and the one we start from. It gives you a real view between open slats without the stack a wider slat builds at the top, and it stays flat across an ordinary bath or bedroom opening.

2 1/2 inch faux wood slat: Fewer slats over the same height, so the face reads cleaner and the open view improves. It also weighs more per running foot, which is exactly why we settle the span and the bracket plan before writing it onto a wide window.

Solid PVC slats: The least expensive construction we hang and the most waterproof. It's also the heaviest, and it's the one most willing to take a bow on hot glass, so we keep it to smaller openings and off the west wall in July.

Wood-polymer composite slats: Wood flour blended with polymer, stiffer and lighter than solid PVC at the same slat size. It costs a bit more and it holds a straight line better on a wide opening or a sunny one, so it's what we specify by default.

Routeless slats: The lift cord runs through a notch at the back edge instead of a hole punched through the face. With the blind closed there's no row of pinholes glowing at you across a dark bedroom. It costs more and it earns it there.

Cloth tape ladders: A woven tape that hides the route holes and lays a color band down the face of the blind. It changes the look more than anything else on the order, and it narrows the view slightly wherever a tape crosses a slat.

Cordless lift: A constant-force spring inside the headrail in place of a lift cord. It's what goes into rooms children use. On a heavy faux wood unit it wants a hand near each end of the bottom rail rather than one hand in the middle.

Tilt wand: A clear or color-matched wand that turns the tilt mechanism. Nothing hangs loose off the headrail, it clears a door handle better than a cord loop does, and it's the default we begin from on almost every faux wood job.

Center support bracket: An extra bracket carried under the middle of a long headrail. On a wide faux wood blind that bracket isn't decoration, it's what keeps the rail from taking a set and the slats from dragging harder on one side than the other.

Two-on-one headrail: Two blinds sharing a single continuous headrail across a wide opening, each with its own lift and tilt. It keeps each unit at a weight the brackets and your arm can manage, and the split position gets written on the order so nobody guesses.

Common Questions

Faux Wood Blinds FAQ

Questions we hear most often from New Palestine homeowners considering faux wood blinds.

Often it won't, and High Acres is the one part of New Palestine where you should assume nothing. Those compass quadrant streets, High Acres East through High Acres West, sit in the town's thin 1940 to 1979 band of 230 units, so you get shallow jambs, thin applied casing, and 1970s aluminum units whose integral track eats the depth a faux wood headrail needs. We measure mounting depth at the stop on every opening rather than reading the kitchen and assuming the back bedroom matches. Where the depth isn't there, an outside mount on the trim looks deliberate and closes the side light gaps at the same time.
Not the slats. PVC ignores steam and it ignores the humid run from late May into September, which is exactly why we put it there instead of hardwood. What wears is mechanical: the ladder string carrying the slats, the tilt gear inside the headrail, the cord lock if there is one. All of that is serviceable without scrapping the blind. In a Cedar Cove kitchen where the opening sits close to the counter run, we specify cordless lift so nothing hangs into the work area, and we set the bottom rail so a raised blind clears the faucet arc.
Two inch, almost always. The 230 units this town built between 1940 and 1979 run 10 to 18 openings and those openings are small, so a 2 1/2 inch slat reads heavy against them and stacks taller when you raise it, which steals view from a window that had little to give away. On the wide rear openings in a post-2000 plan the larger slat closes with fewer gaps between slats and looks better proportioned. We carry both to the measure so you can hold them against your own trim in your own light rather than judging from a photograph.
We can get close, and close is the honest promise. Faux wood is extruded in batches and the whites drift between runs, so a new blind hung beside a two year old one in the same nominal color can read warmer or cooler, especially on a west facing wall that has taken two Indiana summers of low afternoon sun. In a different room nobody will ever notice. On the same wall, we'd rather redo that wall as a set. It's also the argument for ordering a whole house in one run, which in a 16 to 26 opening Willow Ridge plan is a real number of windows.
National ranges are the only honest figure here, because no installed window covering pricing is published for New Palestine or anywhere near it. Nationally, stock shades run about $60 to $600 per window and custom work runs about $250 to $2,600 per window. Faux wood sits in the lower half of that custom range. Width moves it more than anything else, with cordless lift the next largest factor. We quote against your actual window schedule after measuring, and because the Indiana Home Improvement Contract Act applies to residential work over $150, the scope and the total price go in writing before anything is ordered.
A little, and less than the product it gets compared to. A closed 2 inch slat adds a still layer of air at the glass, which helps on a January morning when the average low here is 20.9 degrees, but slats leave routing gaps and the blind doesn't seal at its edges. DOE and Oak Ridge National Laboratory testing credits cellular shades with saving up to 20 percent of heating energy against a bare window. If winter comfort is the reason you're buying, we'll point you at cellular for the bedrooms and keep faux wood for the wet rooms where it genuinely outperforms.
Material, weight and where it belongs. Faux wood is either solid PVC or a wood-polymer composite, and neither one takes on moisture the way a wood slat does. That's the entire reason it exists. The tradeoff is weight. A faux wood slat is heavier per foot than basswood, so the same width that a wood blind handles on its own may need a center support bracket or a two-on-one headrail in faux wood. Across a room you'd struggle to tell a painted faux wood blind from a painted wood one.
No, and that's the specific job we buy them for. A composite or PVC slat has no wood fiber left to swell, so a bathroom running two showers a day doesn't move it, and steam off a stove doesn't either. That's why we put faux wood over sinks, in laundry rooms, in mudrooms and in finished basements in New Palestine without hesitating. What can still happen is heat-driven bowing on a hot sunny window, which is a different failure with a different fix.
Solid PVC can, and you should hear that before you order. A slat sitting behind glass on a west or south elevation gets hot, and a heavy PVC slat that's warm along its whole length will slowly take a slight curve. Composite construction resists it much better because the polymer is stiffened with wood flour. So on a hot exposure we specify composite rather than solid PVC, we keep dark colors off the worst windows, and we suggest tilting the slats open on the hottest afternoons instead of closing them tight.
It depends on the maker, but the honest answer is that width isn't the limit, weight is. Every manufacturer publishes a maximum width and a maximum square footage, and faux wood hits the weight ceiling before wood does. Past a certain span a single headrail starts to settle in the middle, the slats stop lining up, and lifting the blind stops feeling good. Our usual move on a wide opening is either a center support bracket or two blinds on one continuous headrail, decided at the measure rather than after.
Solid PVC is exactly what it sounds like: extruded vinyl, cheapest, fully waterproof, heaviest and the most likely to bow under heat. Composite mixes wood flour into a polymer, which stiffens the slat and drops the weight, and it usually carries a better finish. Composite costs somewhat more. On small bath windows out of direct sun, PVC is honest value. On anything wide, tall or sunny, composite is the one that still looks right in five years, so that's where we spend the difference.
They do, and people notice it at night more than during the day. A standard slat has a hole punched through it for the lift cord, and with the blind closed those holes stack into a vertical line of small bright dots. In a living room nobody cares. In a bedroom facing a streetlight it becomes the thing you look at. Routeless construction moves the cord into a notch at the back edge, and cloth tapes hide the holes behind fabric. Either one solves it.
It isn't, and it's the disclosure worth having in writing. An inside mounted blind has to be narrower than the opening or it would bind against the trim, so the factory takes a small deduction and light comes in down each side. Lutron publishes 3/4 inch per side on their roller product as a real figure, and horizontal blinds behave similarly. If a bedroom in New Palestine needs to be dark, an outside mount that overlaps the trim beats an inside mount every time.
They're heavy, which makes the lift choice matter more than it does on a light shade. We specify cordless in any room a child uses, meaning there's no lift cord anywhere on the product, which is the direction the ANSI/WCMA A100.1-2022 work on cord access points. Inner-cord non-compliance is treated as a substantial product hazard under 16 CFR 1120.3. If a window is wide enough that a cordless faux wood unit gets awkward to lift, that's an argument for splitting it, not for putting a cord back.
That's one of the better places for it. A basement in Hancock County sits cooler and damper than the rest of the house through the muggy stretch from late May into September, and that's the combination that moves a wood slat. Faux wood ignores it. The one thing we check is mounting depth, since basement openings are often shallow and a 2 inch headrail needs somewhere to sit. Where depth runs out we go to an outside mount or drop to a narrower slat.
More forgivingly than almost anything else we sell. Close the slats one way, run a duster or a vacuum brush across the face, then close them the other way and repeat. Marks come off with a damp cloth and mild soap, and unlike wood there's nothing to worry about with water. Don't soak the headrail, because the lift mechanism and the tilt gears inside it don't want to be wet. Cloth tapes need a gentler touch than the slats do.
Probably close, and possibly not exact. Faux wood slats are made in production runs, and white isn't one white. A blind ordered next spring can land a shade off from one hanging now, which nobody notices across a hallway and everybody notices on two windows in the same wall. The fix is simple if you plan for it: order every opening in a room at once, even the ones you're tempted to skip. We write the exact color name onto your paperwork so a future order starts from the right place.
Look at how wide the opening is and how much view you want when the blind is open. The 2 inch slat is our standard and it suits most openings in a New Palestine house. The 2 1/2 inch slat puts fewer slats across the same height, so the face looks calmer and you see more out. It also adds weight, which pushes a wide window toward a support bracket. On a short window a wide slat can look heavy, so we scale it to the opening.
Custom fabrication generally runs two to five weeks, and faux wood usually sits at the shorter end of that because it's a high-volume product. Nothing about that window is a delay, it's a factory cutting slats to your measured sizes. You'll have the fabrication window in writing along with scope, dates and total price, which the Indiana Home Improvement Contract Act requires on residential work over $150. If a date shifts at the factory, you hear it from us the week we learn it.
They do something about both, and we won't overstate either. Closed slats put a solid layer between the room and the glass, and tilting them upward bounces afternoon sun toward the ceiling rather than onto the floor. That's real comfort, though it isn't insulation, and the documented energy testing in this trade sits with cellular shades rather than with blinds. On fading, NFRC puts UV at roughly 40 to 60 percent of the damage, so closing the slats slows fading on floors and furniture. It doesn't stop it.
Areas We Serve

Faux Wood Blinds Across New Palestine

We measure and install in every one of these New Palestine neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in New Palestine

New Palestine Window Treatments handles the full scope of window treatment work. Explore our other services below.

Wood Blinds in New Palestine

Stained hardwood slats matched to real casing, not drywall returns

Learn more →

Vertical Blinds in New Palestine

Vane coverage for the door walls in New Palestine's newest plans

Learn more →

Aluminum Mini Blinds in New Palestine

Thin headrails for shallow jambs where nothing thicker fits

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in New Palestine

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
New Palestine, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 854-7158
Service area

Serving New Palestine and the surrounding area

Call NowGet Quote