Roller Shades

Roller Shades Serving New Palestine, IN

Clean fabric lines for bare drywall returns, light gaps disclosed

Call (317) 854-7158Get Free Quote
Quick Answer

What follows is what we'd tell you in person about this service, including which rooms it belongs in and which ones it doesn't. That second list is shorter but it saves more money.

  • Service: Roller Shades for New Palestine homeowners
  • Service area: New Palestine, IN and surrounding areas
    • How soon depends on which job it is. A new custom order waits on fabrication, typically two to five weeks after the measure. A repair like a restring or a cord lock doesn't wait on anything.
  • Insured and bonded
  • Serving New Palestine, IN since 2008
Roller Shades Services

Expert Roller Shades for New Palestine Homes

Roller shades suit the majority condition in New Palestine, which is a bare drywall return with no applied casing. That describes 53.2 percent of the town's housing, everything from 2000 onward, and it is most extreme in The Preserve, where an 18 to 28 opening plan pairs wide fixed units with stacked rectangular transoms and there is no trim on the wall to compete with. A roller reads as a clean line across the opening. It disappears into a cassette when raised, which is the whole appeal on a modern farmhouse elevation where the window is meant to be the feature and the covering is not.

The disclosure that matters is light gap. Lutron publishes a 3/4 inch per side gap on an inside mounted Roller 20/64 and a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4 to 1 height to width ratio get larger gaps than that. On a bedroom facing the open cropland behind Deer Run, that gap is a visible bright edge at sunrise. Side channels or a light blocking pocket close it, an outside mount over the opening closes it, and nothing else does. Anyone who tells you an inside mounted roller blocks all light is selling.

When to Call

Signs You Need Roller Shades

If you notice any of these in your New Palestine home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

Sun hits the desk for two hours every afternoon

A bedroom stays dim but never actually dark

The bottom bar hangs crooked against the sill line

Existing shades have gone brittle and yellow

Light leaks down both sides of every shade

Fabric rolls crooked and rubs one bracket

A high stairwell window has never been covered

You want one clean line instead of stacked slats

A wide window needs two shades moving together

A bare tube and visible brackets look unfinished

Our Process

How New Palestine Window Treatments Handles Roller Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Window walk with real fabric samples

2

Light gap disclosed per side

3

Brackets leveled, full travel run

4

Openness factor chosen per elevation

5

Battery or hardwired power decided

Real Project Photos

Roller Shades in New Palestine

Photographs from real roller shades jobs completed by our crew in New Palestine and surrounding areas.

Custom shades measured and installed in New Palestine
Scope of Work

What Roller Shades Includes

Every New Palestine job is documented item by item. Here is what the crew covers.

Roll direction decided at the measure, regular or reverse, and written onto the order in plain words

Cranks, locks and handles inside the opening noted, because a regular roll drops the fabric straight onto them

Fascia and reverse roll checked against the manufacturer's own rules, since Lutron doesn't offer that pairing

Three widths and three heights taken per opening, plus a corner-to-corner square check

Mounting depth measured for the tube and bracket, then measured again if a cassette or fascia is wanted

Tube diameter sized to the finished width and the fabric weight so a long roll doesn't sag mid-span

Fabric opacity settled in writing before ordering, light filtering against room darkening against blackout

Side channels and a light-blocking bottom pocket specified where a room has to go dark rather than dim

Light gap per side disclosed at the measure and repeated on the paperwork before the order goes in

Shades over 120 inches tall, or past a 4:1 height-to-width ratio, flagged for larger gaps up front

Factory deduction left with the manufacturer, which is typically 1/16 inch per side

Chain side set window by window so the control lands on the hand you'd naturally reach with

Chain tensioner fastened per the product instructions on every continuous cord loop shade

Cordless and motorized lifts priced where a hanging chain doesn't belong in the room

Hembar chosen against the fabric weight, exposed aluminum or wrapped in the shade fabric

Coupled shades drawn across wide openings so two tubes turn together on a single line

Bracket substrate confirmed ahead of install day so the right anchor or trim screw goes in

Every shade run full travel twice on install day to prove the fabric tracks centered without telescoping

Pricing

What Roller Shades Cost in New Palestine

National category numbers put stock shades near $60 to $600 a window and custom-fabricated shades roughly $250 to $2,600. Those are national ranges for the category and they aren't a quote for anything in New Palestine. Rollers spread across most of that band, because a roller is really a fabric decision wearing some hardware. A basic light filtering fabric on an open roll with a chain sits low. A blackout fabric in a cassette with side channels and a wrapped hembar sits far higher, and it should, since you're buying a light seal rather than a shade. Motorization is its own line, nationally $300 to $1,500 per window installed. New Palestine Window Treatments prices from measured openings across Hancock County.

By Product

How Roller Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

Open roll: The tube and brackets left exposed above the window. It's the least expensive hardware and the most honest looking on a modern opening, though you do see the roll of fabric and the bracket ends from below and from the side.

Fascia: A flat aluminum face that runs across the front of the tube and hides the roll. It gives you a clean horizontal line above the window and it's usually wrapped or powder-coated. Note that reverse roll and fascia don't pair on Lutron systems.

Cassette headbox: A closed box around the tube, open only at the bottom where the fabric comes out. It hides the roll from every angle, keeps dust off the top of the roll, and gives a blackout install somewhere to tuck the top light gap.

Regular roll: Fabric comes off the back of the tube, so it hangs close to the glass. It's the default, it looks tidiest, and it's the roll direction that will foul a crank, a lock or a handle sitting inside the opening if nobody checked.

Reverse roll: Fabric comes off the front of the tube, standing off the glass by an inch or so. Specify it when there's hardware in the opening the fabric has to clear, or when a deep sill would otherwise catch the bottom of the shade.

Light filtering fabric: A woven or vinyl face that passes diffused daylight without a view through it. Rooms stay bright and glare goes soft. It's the everyday specification for a kitchen, a family room or anywhere darkness isn't what you're buying.

Room darkening fabric: A denser fabric that cuts most of the light coming through the face. Bedrooms are the obvious use. Understand that the face is doing the work and the edges are not, so an inside mount still passes light down both sides.

Blackout fabric with side channels: An opaque fabric run inside aluminum channels at each side so the edge light has nowhere to go. Paired with a cassette above and a pocket at the bottom, this is what actually makes a room dark rather than merely dim.

Continuous cord loop with a clutch: A bead chain running over a clutch in the end of the tube, which is the standard manual control. It handles weight well on tall shades. The tensioner has to be fastened to the wall or frame, not left hanging.

Dual bracket: One bracket carrying two tubes at the same window, so a solar screen and a blackout can live together and be used at different hours. It needs mounting depth, which is why we measure for it rather than deciding later.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a New Palestine room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Roller Shades FAQ

Questions we hear most often from New Palestine homeowners considering roller shades.

You either change the mount or add hardware. An outside mount, set above the opening and run wider than it, puts the fabric over the wall instead of inside the return and closes both sides. If the look you want is inside the opening, side channels do the same job with an aluminum track fastened to the return, and a light blocking pocket at the head handles the gap above the roller tube. Both add cost and both are visible. On a drywall return with no casing, which is the standard condition in The Preserve and Willow Ridge, side channels also give the fastener something to hold, which a soft return corner does not.
Regular roll brings the fabric off the back of the tube, close to the glass, which keeps light gaps tighter. Reverse roll brings it off the front, over any handle or projecting trim, and it is what you need when something inside the opening would otherwise catch the fabric. The catch is that reverse roll is not compatible with a fascia, because the fabric now sits where the fascia mounts. If you want the covered front edge and you need the clearance, we solve it with a cassette instead, On the wide fixed units common in The Preserve, roll direction gets settled at the measure rather than at the order, because reversing it afterward means new brackets.
An exposed tube is the cheapest and it shows the roll, which some people dislike and most stop noticing. A fascia is a flat face that hides the tube along the front. A cassette wraps it on more sides and gives you somewhere to build a light blocking pocket. In a house on the 1838 plat with molded casing and real wood jambs, the exposed tube reads as honest and a cassette reads as a box added to old trim. In a 2022 house with nothing but a drywall return, the cassette is what makes the shade look designed in rather than added later.
Two, more often than people expect. A single wide roller sags in the middle of the hembar over time, the fabric can telescope along the tube, and a heavy shade on a long tube is unpleasant to operate by hand. On the wide fixed units common in The Preserve and in current Silverthorne plans, we usually split the opening into two shades under one head treatment so they look like a pair rather than a compromise. The exception is a shade you never touch, on a transom or a high fixed unit, where one wide roller left down permanently is fine.
Cordless is the better default in a house with young children, and ANSI/WCMA A100.1-2022 is the product standard the industry builds to. Cordless has limits though: it needs a reachable hembar, so it is wrong for a two story foyer window or a transom above a fixed unit. A bead chain with a chain tensioner fastened to the return keeps the loop under tension and is the practical answer on tall openings, which the post-2000 New Palestine stock has plenty of. Where a chain is out of the question and the window is out of reach, motorization is the honest recommendation.
The fabric can be genuinely opaque, and that is a separate question from what the installation does. A blackout roller fabric passes no light through the cloth itself. It will still leak at the sides through the gap Lutron publishes at 3/4 inch per side, at the head above the tube, and at the bottom around the hembar. So a blackout fabric on an inside mount gives you a dark room with a bright outline. If the room is a nursery on the east side of a Cedar Creek house, we quote the fabric with side channels and a pocket, or we quote an outside mount and tell you what it will look like.
Roll direction is simply which side of the tube the fabric comes off. On a regular roll it comes off the back and hangs close to the glass, which looks tidiest. On a reverse roll it comes off the front and stands off the glass by an inch or so. It matters because anything living inside the opening, a crank, a lock, a stop or a deep sill, will catch a regular roll. That's a decision made standing at the window with a tape, not afterward from a photo.
On Lutron systems that combination isn't offered, so we design around it rather than pretending otherwise. The reason is geometry: a fascia sits in front of the tube, and a reverse roll brings the fabric down that same front face, so the two want the same space. Other manufacturers handle it differently, and we check the specific line we're quoting instead of stating a universal rule. If you want the fascia look and the fabric needs to clear hardware, a cassette usually solves both.
Open roll is the least expensive and it looks right on a modern opening where exposed hardware isn't a problem. A fascia gives you a flat clean line across the front and hides the roll from below. A cassette wraps the tube on all sides, which hides the roll from every angle and gives a blackout install somewhere to hide the top light gap. Depth is what decides it in practice, since a cassette needs more mounting room than a bare bracket does.
Enough that you should hear the number before you buy. The shade has to be narrower than the opening to travel, so the factory takes its deduction, typically 1/16 inch per side, and light comes down each side of the fabric. Lutron publishes 3/4 inch per side as a real inside-mount figure on Roller 20 and 64. Shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps. If dark is the goal, an outside mount or side channels are the answer.
Room darkening describes the fabric. Blackout describes the whole install. A room darkening fabric blocks most of the light through its face and still passes light around every edge, which is why people call a bedroom dim and feel misled. A genuine blackout is an opaque fabric plus side channels, plus a cassette above and a pocket at the bottom, so the edges are closed too. We separate these in writing before ordering because the words get used loosely everywhere else.
Telescoping is fabric walking sideways on the tube as it rolls, so over a few cycles it creeps toward one end and starts rubbing a bracket. It usually comes from a tube that isn't level, a shade that was forced when it jammed, or fabric cut slightly off square. On a new install it's mostly prevented by mounting the brackets dead level and running the shade full travel twice before we leave. On an existing shade it can sometimes be corrected with shims at one bracket.
Wider than most people need, and the limit is deflection rather than fabric. As a shade gets wide, the tube has to carry its own weight plus the fabric across the span, and a tube that's too small for the width visibly dips in the middle. Manufacturers publish a tube diameter chart against width and fabric weight, and we work from that. Past the practical limit we couple two shades on one line so they turn together and read as a single treatment across the opening.
Chain is the standard and it handles weight best, which matters on a tall shade, but it means a loop hanging beside the window and a tensioner screwed to the wall. Cordless suits smaller shades and rooms where nothing should hang, though a very heavy shade fights a spring. Motors make sense on tall shades, on hard-to-reach windows and on a group you'd rather run together. Hunter Douglas states PowerView battery life is about a year, and batteries are the most under-disclosed cost on a motorized job.
Yes, and it's not a suggestion from us. The tensioner is the small device that anchors the bottom of a continuous cord loop so the chain stays taut against the wall or the frame instead of hanging as a free loop. It ships with the shade, the product instructions require it to be fastened, and a loose loop is exactly the hazard that the ANSI/WCMA A100.1-2022 work on cord access exists to address. We install it as part of the job rather than leaving it in the box.
Yes, on a dual bracket. One bracket carries two tubes at the same opening, so you can run a light filtering or solar fabric during the day and drop a room darkening or blackout shade at night. It's the honest answer when one fabric can't do both jobs, and it beats compromising on a single middle-of-the-road fabric that disappoints in both directions. It needs mounting depth, which is why we measure for the pair rather than adding one later.
Some fabrics curl slightly at the vertical edges over time, particularly lighter weight vinyls in a hot window, and it's a fabric property rather than a defect. Heavier woven fabrics and anything with a knit backing resist it. On the bottom, an exposed aluminum hembar hangs dead straight and is the practical choice on a wide shade, while a hembar wrapped in the fabric looks softer and is better on lighter fabrics. We match the hembar to the fabric weight rather than to a preference.
We can order the same fabric name if it's still in the line, and the color may not be identical. Fabrics run in dye lots, and a bolt woven this year can sit slightly off one woven two years ago, which nobody notices across a house and everybody notices on two windows in the same wall. The practical advice is the same as it is with paint: do a room at once. We write the fabric name and color onto your paperwork so a later order starts from the right reference.
Years, with honest caveats. Solar screen weaves and vinyl-faced fabrics hold up well against direct sun. Lighter decorative fabrics soften and lose color faster on a west or south window than the same fabric on a north one, and the exposed edge that sits outside the roll ages before the rest. Keeping the shade down through the worst afternoon hours actually protects the room behind it, which is the tradeoff. Fading in the room is reduced by the shade, not ended by it.
Two to five weeks is the normal custom fabrication window, with specialty fabrics and anything involving side channels or coupled tubes running toward the longer end. Motorized shades add a step because the tube gets built around the motor. None of that is a delay, it's a factory assembling to your measured sizes. You'll get the fabrication window in writing along with scope, dates and total price, which the Indiana Home Improvement Contract Act requires on residential work over $150.
Areas We Serve

Roller Shades Across New Palestine

We measure and install in every one of these New Palestine neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in New Palestine

New Palestine Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in New Palestine

Moisture proof slats for New Palestine wet rooms and wide openings

Learn more →

Wood Blinds in New Palestine

Stained hardwood slats matched to real casing, not drywall returns

Learn more →

Vertical Blinds in New Palestine

Vane coverage for the door walls in New Palestine's newest plans

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in New Palestine

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
New Palestine, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 854-7158
Service area

Serving New Palestine and the surrounding area

Call NowGet Quote